SA Parts Store
×
-66%

Need installation?? We can do it.
Contact us BEFORE you buy for a better deal on parts and installation! 1.954.477.0443 or Live Chat

Have Questions? Call or Text Us!

  • Guaranteed Fitment

    Always the correct part

  • In-House Experts

    We know our products

  • Added Value

    Performance, Style

  • Wordwide Delivery

    Express shipping on all orders

Rain Scraper Filter for Model 3 Highland & Model Y

TSL3927
protective cover
$11.99 $3.99
Drop-in washer-fluid fill-neck strainer Stop debris at the fill point. Place this removable stainless-steel mesh basket...
$3.99

customers are viewing this product
Rain Scraper Filter for Model 3 Highland & Model Y

Drop-in washer-fluid fill-neck strainer

Stop debris at the fill point.

Place this removable stainless-steel mesh basket inside a compatible windshield-washer fluid opening. It catches leaves, grit and other visible particles while the cap is open or fluid is being added—before they can be poured into the reservoir.

  • 304 stainless-steel mesh
  • No adhesive
  • Removable + washable
  • 1 filter basket
TESERY flange-style stainless-steel washer-fluid fill-neck strainer

The product in five points

A simple barrier for a frequently overlooked opening.

  1. Filters as you refillThe basket sits below the washer-fluid cap and intercepts visible solid debris that could otherwise enter with the fluid.
  2. Fine stainless-steel mesh304 stainless steel provides a rigid, corrosion-resistant screen for repeated contact with washer fluid and rinse water.
  3. No glue or permanent changeThe flange rests at a compatible filler neck without adhesive, drilling or modification to the vehicle.
  4. Lift out for cleaningRemove the basket with the cap open, discard captured debris away from the reservoir and rinse the mesh before reinstalling.
  5. Preventive—not a repair partIt can reduce debris introduced at the fill opening, but it cannot clean a contaminated tank, unblock an existing nozzle or repair a washer-system fault.

Check the opening before ordering

Fit is determined by the washer-fluid filler neck and cap clearance.

A CORRECT MATCH

The current flange-style basket seats flat

  • The basket drops into the washer-fluid opening without force
  • The metal rim rests evenly on the filler-neck ledge
  • The original washer-fluid cap closes and locks normally above it
NOT A CORRECT MATCH

Remove it if the geometry conflicts

  • The rim rocks, tilts or remains raised above the opening
  • The mesh must be crushed, bent or trimmed to enter
  • The original cap becomes difficult to close or no longer seals normally
Listed for Model 3 Highland and compatible Model Y washer-fluid openings.

Tesla filler-neck and surrounding-panel geometry can vary by model year, factory and market. Model Y Juniper, Model YL and other Model 3 / Model Y configurations should be confirmed from the current flange-style product and installation photos. This listing has one size and no separate vehicle variants.

Stainless-steel strainer seated inside a compatible Tesla windshield-washer fluid filler neck

Know exactly where it works

This is a washer-fluid fill strainer—not a rain gutter screen.

Install it under the cap marked with the windshield-and-spray symbol. Its job is limited and useful: catch visible solid debris at that opening.

  • Helps intercept leaves, grit and fragments during a refill
  • Lets washer fluid pass through the mesh into the reservoir
  • Remains accessible whenever the original cap is opened
WHAT IT CAN DO

Add a physical screening step

It reduces the chance of pouring larger visible contaminants through the filler neck and gives you a removable place to collect them.

WHAT IT CANNOT DO

Replace washer-system maintenance

It does not filter the air intake or under-hood rain drains, purify washer fluid, dissolve residue, increase pump pressure, improve worn wiper blades or guarantee that no nozzle will ever clog.

Install and refill

Clean around the opening first, then pour slowly.

  1. Park and identify the capOpen the hood while parked and locate the windshield-washer fluid cap by its spray symbol. Do not confuse it with another service opening.
  2. Clean before openingWipe loose dust and leaves away from the cap so they cannot fall into the filler neck when it is removed.
  3. Seat the basketLower the clean mesh basket into the opening without force and confirm the flange rests flat on the available ledge.
  4. Add proper fluid slowlyPour manufacturer-appropriate washer fluid at a controlled rate. Fine mesh can slow the flow; pause if fluid begins pooling near the rim.
  5. Clear and closeRemove captured debris, reseat the clean basket and close the original cap. Stop using the basket if the cap cannot close normally.
Never push captured debris through the mesh.

Lift the basket out carefully and empty it away from the open reservoir. Keep tools, fingers and loose objects out of the filler neck, and avoid handling damaged mesh with bare hands.

Maintenance that preserves the benefit

A full or dirty screen becomes a bottleneck.

INSPECT

Look before every refill

Check for trapped leaves, sediment, deformation and sharp or separated mesh before pouring fluid.

RINSE

Clean outside the vehicle

Remove the basket, rinse from the clean side toward the debris side, and use a soft brush only if necessary.

REINSTALL

Dry and seat it flat

Allow it to drain, reinstall without forcing and verify the original cap still closes exactly as it did before.

Product facts

One removable screen with a clearly defined job.

Item Current product information
Product type Windshield-washer fluid filler-neck strainer / filter basket
Current shape Round stainless-steel mesh basket with a flat support flange, as shown in the current main image
Listed application Model 3 Highland and compatible Model Y washer-fluid openings; verify the actual filler-neck and cap geometry for Model Y Juniper, Model YL and other vehicle configurations
Material / color 304 stainless steel / silver
Installation Drop-in, removable placement; no adhesive, drilling or tools
Function Intercepts visible solid debris at the washer-fluid fill opening while allowing fluid to pass through
Package 1 × washer-fluid filter basket
Care Remove and rinse as needed. Replace the product if the flange or mesh is bent, split, loose or sharp.

Before you order

Washer-fluid strainer FAQ

Where does this filter go?

It sits inside a compatible windshield-washer fluid filler neck, directly under the cap marked with the windshield-and-spray symbol. It is not installed in the cabin-air intake or an under-hood rainwater drain.

Will it fit every Model 3 and Model Y?

No single drop-in basket should be assumed to fit every filler-neck revision. The current listing shows a flange-style basket for Model 3 Highland and compatible Model Y openings. Compare your opening, ledge and cap clearance with the current photos before ordering.

What about Model Y Juniper or Model YL?

Use the filler-neck geometry as the final check. The basket must drop in without force, rest flat and allow the original cap to close normally. Do not bend or trim it to make an incompatible opening work.

Can it prevent every washer nozzle blockage?

No. It helps stop visible debris introduced through the filler opening, but blockages can also come from unsuitable fluid, dried deposits, contaminated tanks, freezing, pump or hose problems and nozzle damage.

Why does washer fluid pass through more slowly?

Fine mesh restricts flow more than an open filler neck. Pour slowly and pause if fluid pools near the rim. A noticeably slower flow can also mean the screen needs cleaning.

Can I leave the basket installed under the cap?

Yes, provided it sits flat and the original cap closes and locks normally without extra force. Remove the basket if it changes cap operation or sealing.

Does it require adhesive?

No. The basket is designed to rest in a compatible filler neck and remain removable for cleaning. Do not glue or tape it in place.

What is included?

One 304 stainless-steel washer-fluid filter basket. Washer fluid, tools and decorative items shown in application images are not included.

Can I return it if the opening does not match?

Keep the basket clean, unused and unmodified while checking the opening. Do not bend, trim or glue it. Return eligibility is governed by the current refund policy.

Read More
Read Less

All products are shipped out from one of the Signature Autohaus shipping locations. Signature Autohaus drop ships some products and ships direct others. All products are shipped via FedEx, UPS, DHL or another qualified shipping carrier. Special arrangements may need to be made for international orders and oversize packages. In the event a product arrives damaged to your location, please follow the steps listed below. All damaged items must be reported to the shipping carrier immediately and you must notify Signature Autohaus within 5 days of receiving your order. If these steps are not followed, your shipment may not be able to be a candidate for a claim. Complete the Shipping DAMAGE Claim Form by contacting the carrier that delivered your package. 1) Keep the product and its original packaging and box Make a list of the damaged or lost item(s) 2) Signature Autohaus will contact the shipper once we receive the email info above to schedule a pickup, DO NOT send it back to us 3) Once the product is picked up and inspected by Signature Autohaus and or Supplier, a replacement or credit will be issued. 4) The Shipping Rates shown at time of checkout our dimensional rate only. If your shipment weight is to much then contact us for a shipping quote. If there is an error in the shipping rate quoted we will contact you and let you know of the changes. International orders(Outside the USA) are not automatically processed as we may require additional information from you. If a product is ordered and not wanted, the UNUSED item can be returned for a 35% restocking fee. Shipping is not refundable in either direction. All items wanting to be return MUST be reported within 30 days of the original invoice date. No items will be returnable after 30 days. All products shipped from the Signature Autohaus warehouse are shipped via FedEx or Freight and require a signature when delivered. Some packages shipped from the manufacturer may or may not require signatures for package release. Fedex, UPS, and DHL have package pick up locations if you are unable to sign for the package. If the package is returned to Signature Autohaus or manufacturer, you will be responsible for the return shipping costs and pay a 35% restocking fee. These fees will be charged to your account on file. SIGNATURE AUTOHAUS DOES NOT REFUND SHIPPING CHARGES. If you modify, install, or alter the item in any form, we cannot accept it as a return, will not cover any expenses related to the product or installation, and you maybe be required to purchase a replacement. In the event that the product you ordered is sent either incorrectly or processed wrong by Signature Autohaus, we will arrange for the package to come back to us and ship out a replacement. We will evaluate the situation before we determine the shipment was incorrect. To return a item back to us, please do the following: 1. Contact our Customer Service Department to receive a RMA number. All packages returned without a Returned Merchandise Authorization number will be refused. 2. Package the item up in original packaging unless deemed unuseable 3. Include the UNUSED parts and any additional information that was included 4. Include a copy of your receipt 5. Write a brief description of the problem with the product 6. If you have a receipt for the return shipping include as well 7. We DO NOT accept any freight collect packages 8. Once we have received the above information we will notify you via email or phone and let you know the status.

We use cookies to improve your experience on our website. Read about how we use cookies in our Privacy Policy. By browsing this website, you agree to our use of cookies. privacy policy
accept

Your cart

×